Last seen: Jan 24, 2023
We are seeing very similar behaviour with our flow temps. After a couple of weeks of nice sunny days here it has now become colder and cloudier, so ...
So, ran our system in Room Temperature mode for a week or so, and monitored flow temperatures. I came to the conclusion that it doesn't work very wel...
@alec-morrow sorry for the slightly delayed response - just been fighting off Covid! I'm a little unsure about what you mean. Would mixers enable e...
@kev-m Yes, it is the Mitsubishi wireless controller that I am using. You raise an interesting point because obviously there is no way to have tw...
@kev-m A quick update. After thinking about the problem for a little while and re-reading the manual I came up with really simple solution - swap th...
@kev-m Thanks for that information, it confirms what I thought was happening. I'm not going to write off Room Adaptation just yet, but may have t...
@alec-morrow FTC is the Mitsubishi Flow Temperature Controller The ASHP was retrofitted so the UFH uses controller and stats from Uponor as origin...
I found that when taking images outside it was better to go closer so that there was no sky in the frame. The sky shows as a lot colder than the hous...
@skd @SuzeR We also have an 11.2kW Ecodan. Generally very quiet except when the ambient drops. We only have one internal pump (something I am stil...
Our towel rails are in the same circuit as the upstairs radiators, so only get warm when the heating is on, with one exception. The ensuite in our ma...
I understand what you're saying, but it's not just that the guy who came yesterday thinks it is sub-optimal, it is actually wrong. Continuing to run ...
Latest Posts
-
RE: Location of hot water isolation valve on cylinder
@rossowheels if you isolate the water supply in it will...
By ASHP-BOBBA , 4 hours ago
-
RE: Ecodan consuming 100kwh per day in new build!!!
From what you say about the radiators upstairs it does ...
By JamesPa , 10 hours ago
-
RE: Compressor attempts start but fails - Nibe Fighter 2005 8kW
@skyefarmer pleased you found it!
By JamesPa , 11 hours ago
-
The Importance of Radiator Balancing for Efficient Heating: Introducing the Flow Regulating Valve
It’s fascinating to watch how low-temperature heating i...
By Mars , 13 hours ago
-
@heacol, if you're around, can you please provide some ...
By Mars , 16 hours ago
-
RE: Servicing Hitachi HP in rural Somerset
I'd give GreenGenUK a call or email them: sales@greenge...
By Mars , 16 hours ago
-
RE: Heating coming on when not required
I played with a max heating temp but there is a world o...
By JamesPa , 1 day ago
-
RE: Pressure drop Primary circuit
I've always regarded topping up heating systems as my j...
By JamesPa , 1 day ago
-
RE: Heat pump solutions and/or installer recommendations for France
I’d travel to France for work if you were struggling wi...
By Damon Blakemore , 1 day ago
-
RE: 5 Star Service from Havenwise
That's always a danger with any new good idea, @morgan....
By Majordennisbloodnok , 2 days ago
-
Have your say in the Renewable Heating Hub Awards
It’s time to celebrate the best (and call out the worst...
By Mars , 2 days ago
-
-
RE: Mitsubishi cycling while on chilled water output
@iaack yes there's no denying that cold air sinks! I s...
By downfield , 3 days ago
-
RE: Weather compensated secondary circuits with Biomass
@andycoo that flooring sounds ideal. Extra volume is ...
By Sune , 3 days ago
-
If you are thinking of heating on the immersion conside...
By JamesPa , 4 days ago
-
RE: Surface mount or bury primaries for heat pump installation?
@tomasmcguinness, I think your best bet would be using ...
By Aventus Eco , 4 days ago
-
RE: Solar Power Output – Let’s Compare Generation Figures
@toodles all depends on asking the right questions! And...
By Tim441 , 4 days ago
