Forums

Forums
Members
Gary
Activity
 
Notifications
Clear all
Gary
@gary
Member
Prominent Member
Joined: Feb 8, 2023
Last seen: Jul 31, 2025
Profile Activity
Topics: 2 / Replies: 348
AllTopicsReplies
Reply
RE: The Definitive Guide to Weather Compensation and Curves for Air Source Heat Pumps

7 months ago
Forum
Air Source Heat Pumps (ASHPs)
Reply
RE: The Definitive Guide to Weather Compensation and Curves for Air Source Heat Pumps

The Ecodan WC curve doesn’t have presets like you see in other systems it’s fully customisable. So you can set the high and low end at any OAT and ch...

7 months ago
Forum
Air Source Heat Pumps (ASHPs)
Reply
RE: ASHP and how it should run and potential kw consumption?

My heat pump by luck is sized correctly and defrosts hourly. All you can do is keep the flow temp to the minimum you need and keep it running so you ...

7 months ago
Forum
Air Source Heat Pumps (ASHPs)
Reply
RE: ASHP and how it should run and potential kw consumption?

I have an 8.5kw heat pump and its currently running at 36C and pulling 2kw so not miles away from yours, when it runs at 45C its will pull 3.5kw, ther...

7 months ago
Forum
Air Source Heat Pumps (ASHPs)
Reply
RE: Analysing MELcloud heat pump graphs

@boycey If you are running at 26C and the house is 20C then your UFH isn't going to be able to get rid of any heat as the room temp is too close to th...

7 months ago
Forum
Air Source Heat Pumps (ASHPs)
Reply
RE: Analysing MELcloud heat pump graphs

if you click on tank temp and set temp in the legend it will remove them from the plot it will rescale you will then be able to see what the flow tem...

7 months ago
Forum
Air Source Heat Pumps (ASHPs)
Reply
RE: Analysing MELcloud heat pump graphs

That will just prevent the heat pump from setting a temperature lower than 30C, its easier just to adjust your weather compensation curve. Can you po...

7 months ago
Forum
Air Source Heat Pumps (ASHPs)
Reply
RE: Analysing MELcloud heat pump graphs

Just to add my 2p, I have an Ecodan and UFH, to avoid cycling on and off then we need set the flow temp at a minimum of 32C, from your plots it looks ...

7 months ago
Forum
Air Source Heat Pumps (ASHPs)
Reply
RE: L9 error with Mitsubishi ecodan heat pump

As you state L9 is flow rate error, if you go to the service menu when the heat pump is running and then go into running information and put in code 5...

8 months ago
Forum
Air Source Heat Pumps (ASHPs)
Reply
RE: What’s your ASHP delta T?

between 3 and 8 depending on flow temp, Ecodan so fixed flow rate.

8 months ago
Forum
Air Source Heat Pumps (ASHPs)
Reply
RE: Noise Issues with our Ecodan 8.5kW WM85VAA air source heat pump

@athlonoc you don't have a mitsubishi preplumbed cylinder so the FTC probably can't control the pump speed but that is easy to check on the FTC go to ...

8 months ago
Forum
Air Source Heat Pumps (ASHPs)
Reply
RE: Noise Issues with our Ecodan 8.5kW WM85VAA air source heat pump

@athlonoc You don't need 24L/min for an 8.5kw heat pump, Mitsubishi's own manual states 15.2L/min, 24L is the absolute maximum so i'm not surprised it...

8 months ago
Forum
Air Source Heat Pumps (ASHPs)
Page 13 / 30
Share:

Join Us!

Podcast Picks

Latest Posts

Click to access the login or register cheese
x Powerful Protection for WordPress, from Shield Security
This Site Is Protected By
ShieldPRO →