Last seen: Apr 7, 2025
@gary some the trends you've posted show the LWT is at the setpoint. They also show the setpoint is changing and they show the compressor frequency ...
Hello, I confused about why this is a problem for you. Is your house not getting warm enough? Thanks Bob
@gary I'll try and help, but at the moment I'm not really sure what the problem is. <rant> On a more general note, I read threads like this...
The lower the DT the higher the flow rate. The lower the DT on the heating water side, the hotter the average temperature of the heat emitter, so th...
@jamespa I don't know where this comes from. I've heard a variety of numbers mentioned for heating design. 10C, 5C, 7C. I think it comes from ...
Hello @jamespa I've attached a spreadsheet which attempts to show how a heat pump compressor system works. The gas enters the compressor as a s...
OK, so I'm just thinking out loud here: You loose energy through the walls, roof, and draughts - anywhere else? The 10% lost energy could be going...
Hello, sorry I've been quiet for a while. In CathodeRays case the plate heat exchanger was acting as restriction in the flow of energy from the heat...
@cathoderay at constant room temperature, energy in = energy out Q = UA.DT tells you how much energy flows through an object, in this case a wall, w...
Slicing and dicing data can sometimes be fun, but it's often frustrating. I often start by asking "what do I think i'm looking for". So..."does se...
@cathoderay what would the plot look like if you used (Inside temp - Outside temp) as the x-axis? If Q = UA.DT the gradient of the trend would be UA...
@transparent, thank you. That makes sense. Much appreciated. Regards Bob
Latest Posts
-
RE: Mitsu Wireless Controller and MelCloud
@davidalgarve If they are 'off' because of a timed s...
By Morgan , 30 minutes ago
-
RE: Heat Pump Servicing & Maintenance – Good Value or Rip-Off?
For reference, our installer has just contacted us afte...
By Old_Scientist , 23 hours ago
-
@toodles Of course. I've also used Tim and Kat's Gree...
By Old_Scientist , 24 hours ago
-
RE: Who's your electricity provider and what's your tariff?
Yes, I noticed that change too. The software really doe...
By Old_Scientist , 24 hours ago
-
RE: Octopus Cosy & Octopus EV + bidirectional smart tariff, together. What, eh?
@old_scientist me too. Just installed my new heat pump ...
By Eliuccio , 2 days ago
-
RE: Is your heat pump insured?
Yup just spoke to Privilege to inform them of my impend...
By Scalextrix , 2 days ago
-
RE: Forum updates, announcements & issues
Just to keep everyone in the loop, as the site continue...
By Mars , 2 days ago
-
RE: Fast DHW setting on Midea (Clivet) heat pump
@simon-w, is this something you could potentially assis...
By Mars , 3 days ago
-
RE: Share Your Experiences with Heat Pump Manufacturer Support
Fwiw I called my installer out for the first time a few...
By JamesPa , 3 days ago
-
RE: New Vaillant aroTherm Plus in black - When will it come to the UK?
@sandy, I'll send Vaillant an email tomorrow and see if...
By Mars , 3 days ago
-
RE: Long term efficiency degradation
@jamespa yes as I thought thanks. We have a reaso...
By Scalextrix , 3 days ago
-
RE: Who has a V2G EV installation
I agree, but a word of caution. V2X is also sometimes u...
By Majordennisbloodnok , 4 days ago
-
RE: Sunamp Thermino Heat Battery
@jamespa A few days after the installation had been com...
By Toodles , 4 days ago
-
RE: Planning Permission May 2025
Fair enough. I have read the legislation and MCS020a ...
By JamesPa , 6 days ago
-
RE: How do I choose a single room MVHR to prevent losing heat in my bathroom ?
An update on the Heatsava. It is the most difficult thi...
By heat-pump-newbie , 6 days ago
-
RE: ASHP heat output monitoring
@carlo - not much better, is it. It looks more like a u...
By cathodeRay , 7 days ago
-
RE: Renewables & Heat Pumps in the News
this document extensively describes (in a non-blame, ne...
By Judith , 1 week ago
-
RE: Ecodan - Legionella Operation Time and Target Temperature
Once the white plastic cap is removed, my immersion loo...
By Old_Scientist , 1 week ago
-
RE: Replacing Refrigerant on Mitsubishi Heat Pump
@dgclimatecontrol I don't know, but they were not happy...
By DavidAlgarve , 1 week ago
-
RE: Why do we need pressurised systems?
A good question @toodles. My old open thermal store and...
By AllyFish , 1 week ago
