Forums

Forums
Renewable Heating
Air Source Heat Pum...
12kW Samsung gen 6 ...
 
Notifications
Clear all

12kW Samsung gen 6 short cycling

 
Page 13 / 32
Air Source Heat Pumps (ASHPs)
Last Post by iantelescope 2 years ago
374 Posts
17 Users
63 Reactions
76.5 K Views
RSS
 Craig1980
(@craig1980)
Reputable Member Member
Joined: 3 years ago
Posts: 146
Topic starter 29/11/2022 12:14 am  

Still cycling at 8 mins on 20 seconds off with room stats at 25 degrees. Water outlet (flow temp I assume) is up a couple of degrees but the outside temp has also dropped tonight. 



   
ReplyQuote
 Derek M
(@derek-m)
Illustrious Member Member
Joined: 5 years ago
Posts: 4427
29/11/2022 11:47 am  

Posted by: @craig1980
↑

Still cycling at 8 mins on 20 seconds off with room stats at 25 degrees. Water outlet (flow temp I assume) is up a couple of degrees but the outside temp has also dropped tonight. 

Hi Craig,

To try to find the root cause of the problem, it is necessary to observe how your system is actually operating, and compare this against how we think the system should be operating.

Below are a few checks and observations to make.

Carefully time how long the system is 'on' and how long the system if 'off', ideally to the nearest second. We can then see if there is any variations.

Record the changes in the readings displayed on the controller for LWT, outdoor temperature, and any other temperature and flow readings that are available. Pay particular attention to changes from just before the heat pump stops, during the 20 second shutdown period, and after the heat pump restarts.

 



   
ReplyQuote
 Craig1980
(@craig1980)
Reputable Member Member
Joined: 3 years ago
Posts: 146
Topic starter 29/11/2022 11:52 am  

I'll do that today and report back. Thanks 



   
ReplyQuote
 Derek M
(@derek-m)
Illustrious Member Member
Joined: 5 years ago
Posts: 4427
29/11/2022 1:59 pm  

@craig1980

I have attached a copy of a manual which details all the various parameter settings, which are listed from page 24 onwards.

I would suggest that you go through your system and make a note of all the values.

Samsung DB68-08470A-03_IB_EHS_Wired_Remote-Control_Kit_EU_Book_EN_200331.pdf


   
ReplyQuote
 Craig1980
(@craig1980)
Reputable Member Member
Joined: 3 years ago
Posts: 146
Topic starter 29/11/2022 4:35 pm  

I have my doubts over this section. 

20221129 152900

 

Could this be set incorrectly? 

20221129 152904

Its set the same for this and external thermostat application #1 (floor) and #2 (FCU).

I have no UFH so is the "floor" part irrelevant or have the set the zone 1 and 2 up as "floor" and "FCU" respectively? 

I've also just changed the 2041 Heating water law for auto mode to WL2-FCU from WL1-Floor. Is that the right thing to do as I don't have UFH? 



   
ReplyQuote
 Derek M
(@derek-m)
Illustrious Member Member
Joined: 5 years ago
Posts: 4427
29/11/2022 4:41 pm  

@craig1980

My idea was to first gather the information, then give it a close dose of inspection, and then try to decide what needs to be changed.



   
ReplyQuote



 Craig1980
(@craig1980)
Reputable Member Member
Joined: 3 years ago
Posts: 146
Topic starter 29/11/2022 4:45 pm  

@derek-m no problems, it's just something I'd seen before but wasn't sure if it was correct.



   
ReplyQuote
 Derek M
(@derek-m)
Illustrious Member Member
Joined: 5 years ago
Posts: 4427
29/11/2022 6:20 pm  

@craig1980

Based upon normal operation, I would expect your system to perform in the following manner when in WC mode.

The outdoor air temperature sensor measures the ambient air temperature and conveys this reading to the controller. The controller calculates the required LWT. If either of the room thermostats are calling for heat, and the actual LWT is below the calculated value, by a specified margin, then the heat pump will start operation.

When the actual LWT exceeds the calculated value, by a specified margin, the heat pump will stop operation. When the actual LWT falls below the calculated value, plus the specified margin, the heat pump should restart. This process will probably continue during milder ambient temperatures.

What values did you record during the monitoring process?

 



   
👍
1
ReplyQuote
 Craig1980
(@craig1980)
Reputable Member Member
Joined: 3 years ago
Posts: 146
Topic starter 29/11/2022 8:03 pm  

@derek-m I'm just doing the monitoring now. 

Where would I find the LWT? I'm assuming that's leaving water temp? I have my thermometer now 



   
ReplyQuote
 Derek M
(@derek-m)
Illustrious Member Member
Joined: 5 years ago
Posts: 4427
29/11/2022 8:29 pm  

Posted by: @craig1980
↑

@derek-m I'm just doing the monitoring now. 

Where would I find the LWT? I'm assuming that's leaving water temp? I have my thermometer now 

The LWT is what is labelled Current Water Outlet on the 'normal' display on the controller.

I assume that your heat pump is still switching back on after only 20 seconds?

The objective of the testing, is to see what is happening to the various temperatures around your heat, as it stops and then restarts. Since the heat pump should not normally restart after only 20 seconds shutdown, something must be causing it to do so.

 



   
ReplyQuote
 Craig1980
(@craig1980)
Reputable Member Member
Joined: 3 years ago
Posts: 146
Topic starter 29/11/2022 8:47 pm  
20221129 192642
20221129 192634
20221129 192553
20221129 192621
20221129 192517
20221129 192533

Images of all figures and settings on the field settings manual. I hope it makes sense?

It is on for exactly 7 mins 58 second and off for exactly 20 seconds. 

Water outlet 24.8 turns off 24.8 turns on at 21.5 indoor temp on wired remote but 18.5 on room stats confirmed by independent stats. Climbs to 27.2 at the middle of the cycle and drops back to 24.8 by the end. 



   
ReplyQuote
 Craig1980
(@craig1980)
Reputable Member Member
Joined: 3 years ago
Posts: 146
Topic starter 29/11/2022 8:57 pm  

Just checked flow and return temps on rad closest to UVC and it's 25.2 -22.6



   
ReplyQuote



Page 13 / 32
Forum Jump:
  Previous Topic
Next Topic  



Share:

Join Us!

Podcast Picks

Latest Posts

Click to access the login or register cheese
x Powerful Protection for WordPress, from Shield Security
This Site Is Protected By
ShieldPRO →