Last seen: May 15, 2025
Agreed, but as we are looking at something that's set to run 24/7 then the other featured don't need to be changed / looked at. So if does decide to t...
Nice looking controller, follows much the same as other ones. Would need to see some documentation about advanced mode, as ideal could be setting up t...
@jamespa I don't think any system, without lots of hardware will be able to balance emmitters. That will always be done by hand etc. Yes Homely c...
As I've stated before a good add on controller, working with IAT and adjusting flow temp, will cover nearly all the problems we have encountered. Al...
I would say your heat loss for the house is about right. I take it at 5kw, but never bothered to work it out myself, and that would fall into the righ...
@ajbevster Okay, I think I understand now, but might not have it all correct. The Glenhill has its own internal 70l buffer and 300l cylinder and the...
Cheers, I think the 72l one can be ignored, could be there as a volumizer and shouldn't effect flow/return. Is the Gledhill your DHW system ? Not...
Normally I don't like asking lots of questions, but here we may need some more information - Do you have a buffer/low loss header or volumizer in th...
@transparent Glad I could help, without realising it. Going for a tea and a read of your guide.
Thank you, yes we have MVHR system. That's what I have been saying and hence the reason we run it the way we do. I've since learned not to criti...
@heatgeek It's very much passive house and at 538m², with 1300kwh heating (as taken from a meter just for the HP). That works out at less than 2.5...
@heatgeek Thank you, yes this is quite a meal and I'll try to understand each part. --- "efficiently use such a large HP to directly heat yo...
Latest Posts
-
RE: Compressor attempts start but fails - Nibe Fighter 2005 8kW
@skyefarmer great you located the source of the issue a...
By Mars , 3 hours ago
-
RE: Location of hot water isolation valve on cylinder
@rossowheels if you isolate the water supply in it will...
By ASHP-BOBBA , 12 hours ago
-
RE: Ecodan consuming 100kwh per day in new build!!!
From what you say about the radiators upstairs it does ...
By JamesPa , 18 hours ago
-
The Importance of Radiator Balancing for Efficient Heating: Introducing the Flow Regulating Valve
It’s fascinating to watch how low-temperature heating i...
By Mars , 21 hours ago
-
@heacol, if you're around, can you please provide some ...
By Mars , 24 hours ago
-
RE: Servicing Hitachi HP in rural Somerset
I'd give GreenGenUK a call or email them: sales@greenge...
By Mars , 24 hours ago
-
RE: Heating coming on when not required
I played with a max heating temp but there is a world o...
By JamesPa , 2 days ago
-
RE: Pressure drop Primary circuit
I've always regarded topping up heating systems as my j...
By JamesPa , 2 days ago
-
RE: Heat pump solutions and/or installer recommendations for France
I’d travel to France for work if you were struggling wi...
By Damon Blakemore , 2 days ago
-
RE: 5 Star Service from Havenwise
That's always a danger with any new good idea, @morgan....
By Majordennisbloodnok , 2 days ago
-
Have your say in the Renewable Heating Hub Awards
It’s time to celebrate the best (and call out the worst...
By Mars , 3 days ago
-
-
RE: Mitsubishi cycling while on chilled water output
@iaack yes there's no denying that cold air sinks! I s...
By downfield , 3 days ago
-
RE: Weather compensated secondary circuits with Biomass
@andycoo that flooring sounds ideal. Extra volume is ...
By Sune , 3 days ago
-
If you are thinking of heating on the immersion conside...
By JamesPa , 4 days ago
-
RE: Surface mount or bury primaries for heat pump installation?
@tomasmcguinness, I think your best bet would be using ...
By Aventus Eco , 5 days ago
