Last seen: Nov 12, 2025
Mitsubishi iLife 2 slim./p>
Sitck with it, if you get your WC curve down to the lowest possible consistent with heating the house you should have an efficient system and plenty o...
Just to say you do need a firm tap (occasionally several), just opposite the inlet to the radiator. Hit it about as hard as you dare. Sometimes this...
So deltaT across rad circuit = 37.9-24.4 = 13.5C. ~5C is what we are looking for. So Im expecting the return from rads to be more like 32C than 24...
Yes. If the pin feels sprung then no problem. If it moves freely then the closing piece (not sure what it's called) may be stuck. A few sharp taps ...
You adjust the end points of the sloped line.you presented earlier. This will be somewhere in the menu, probably the installer menu. I would reduce ...
Yes thanks, good plot Yes initially, but then you turn down the weather compensation curve until the house is at just the right temperature, that...
Situation normal then as @tim441 says you are almost certainly going to have to meddle if you want your system to work efficiently. T...
Black thing looks like (probably) a low loss header combining the output of the two pumps. You will get complete mixing in that which could in princi...
On the grounds that turning the pump speed down didnt help I would put it back up again. Slow flow = higher deltaT across radiators = higher FT neede...
Quite likely not but...with two pumps you have the opportunity to get a very good turndown/modulation ratio and a level of redundancy against failure....
- 26 Forums
- 2,283 Topics
- 51.1 K Posts
- 241 Online
- 5,944 Members
Join Us!
Podcast Picks
Latest Posts
-
RE: Installer Fitted 9kW Instead of 11kW Heat Pump and Changed MCS Paperwork - What do I do?
And here is what the Homely plots say for the last few ...
By Toodles , 17 minutes ago
-
RE: Havenwise App Help & Forum Support – Get the Most from Your Heat Pump
@hcas Thanks! One more question - are you able to tak...
By nickhorne , 1 hour ago
-
Extend the colder range of the weather compensation curve?
In theory everyone has a heatpump designed to deliver t...
By TheBinMan , 2 hours ago
-
RE: Faulty Clivet heat pump out of the box
@steveimpey I’m always watching 👀My Clivet cont...
By Mars , 6 hours ago
-
RE: When to use Octopus Intelligent Go tariff with my heat pump and battery
@treewizard That's probably fine, provided as you say...
By GrahamF , 7 hours ago
-
RE: Air source heat pump roll call – what heat pump brand and model do you have?
16Kw AIROSD Manufacturer: Foshan Model: QBKFXFC-...
By Polar bear , 7 hours ago
-
Just a suggestion but upload your images to an AI agent...
By RadWhisperer , 9 hours ago
-
RE: Daikin Wireless Thermostat
The switch from WDC to LWT i.e. pure WC is fairly strai...
By RadWhisperer , 9 hours ago
-
RE: Bosch CS5800i 5kW - Experience So Far
Thank you for your continuous research, and posts. As y...
By ectoplasmosis , 17 hours ago
-
RE: Trying to understand my Nibe F1245
@barry-sharp, is this something you could help with?
By Mars , 18 hours ago
-
I signed up for this, I think it will be a good one. Al...
By ASHP-BOBBA , 22 hours ago
-
RE: Heat Loss v Outside Air Temperature
Ideal conditions to collect the data! Although the left...
By cathodeRay , 23 hours ago
-
RE: My DIY Heat Pump installation
@majordennisbloodnok The 'more' button takes me to ...
By Polar bear , 23 hours ago
-
RE: Aira Heat Pump: Stylish Scandinavian Heating
@vsmith1 If you have access to Home Assistant then you ...
By Gmuzz , 24 hours ago
-
Aira Intelligence: integrated home energy system
Aira has just announced a new integrated home energy sy...
By Mars , 1 day ago
-
RE: Low COP and unevenly heated rooms with 12kW Samsung AE120MXTPEH / AE260TNWTEH
i cant trace it. Near the pumps in the basement it seem...
By bonobo , 1 day ago
-
Daikin Altherma Heating Controls using Onecta Integration via Home Assistant
Ok so likely not setting the world on fire here for rev...
By phil bell , 1 day ago
-
RE: Who's your electricity provider and what's your tariff?
So I’m still with E.ON Next, and I received a pretty sn...
By Mars , 2 days ago
-
RE: First time wall mounting an ASHP
what you need to do is everything you can to remove the...
By ASHP-BOBBA , 2 days ago


