Last seen: Feb 18, 2025
Heating engineers out today and my fault is the expansion vessel for the dhw cylinder. It started making this noise like a foghorn on Saturday and ha...
@toodles the installer coming out tomorrow toodles. I was curious if the tundish routinely blew off or if it’s a fault but looks like a fault or they ...
@toodles a bit confused toodles, no idea what’s blowing off the expansion vessel of the tundish but it was loud. I checked my pressure on the gauge a...
Just noticed I have lost my pressure and had to recharge. I have a thought it’s the mains water pressure that’s too high.
@ellyse the icons you can get online and what they do. You will need to do that so you know how to lower dhe temp. The pump speed is determined by fl...
@transparent you can get all the paperwork they hold on you by submitting a data request, GDPR I think it’s called now. Total rubbish refusing to give...
@transparent is that relief valve on the cylinder a built in g4, mine was high up on the pipework with an air gap. It all looks a bit how mine was, th...
@toodles my daughters is similar and I installed it. I reduced the temp but without gauges I have no idea what flow and return temps are. I need to t...
@jamespa once it all goes wrong and you research you then realise how bad. When you confront the installer they don’t understand. Change isn’t coming ...
@jamespa mine was costing me 25 quid a day and I had my log burner running. It might be a free grant she has but it will bankrupt her unless it gets k...
I did a quick check and I’m told if it’s y plan then you don’t have independent control over domestic hot water and heating, but one of the other boff...
- 26 Forums
- 2,102 Topics
- 46.2 K Posts
- 100 Online
- 3,388 Members
Join Us!
Latest Posts
-
RE: Compressor attempts start but fails - Nibe Fighter 2005 8kW
@skyefarmer great you located the source of the issue a...
By Mars , 3 hours ago
-
RE: Location of hot water isolation valve on cylinder
@rossowheels if you isolate the water supply in it will...
By ASHP-BOBBA , 12 hours ago
-
RE: Ecodan consuming 100kwh per day in new build!!!
From what you say about the radiators upstairs it does ...
By JamesPa , 18 hours ago
-
The Importance of Radiator Balancing for Efficient Heating: Introducing the Flow Regulating Valve
It’s fascinating to watch how low-temperature heating i...
By Mars , 20 hours ago
-
@heacol, if you're around, can you please provide some ...
By Mars , 23 hours ago
-
RE: Servicing Hitachi HP in rural Somerset
I'd give GreenGenUK a call or email them: sales@greenge...
By Mars , 24 hours ago
-
RE: Heating coming on when not required
I played with a max heating temp but there is a world o...
By JamesPa , 2 days ago
-
RE: Pressure drop Primary circuit
I've always regarded topping up heating systems as my j...
By JamesPa , 2 days ago
-
RE: Heat pump solutions and/or installer recommendations for France
I’d travel to France for work if you were struggling wi...
By Damon Blakemore , 2 days ago
-
RE: 5 Star Service from Havenwise
That's always a danger with any new good idea, @morgan....
By Majordennisbloodnok , 2 days ago
-
Have your say in the Renewable Heating Hub Awards
It’s time to celebrate the best (and call out the worst...
By Mars , 2 days ago
-
-
RE: Mitsubishi cycling while on chilled water output
@iaack yes there's no denying that cold air sinks! I s...
By downfield , 3 days ago
-
RE: Weather compensated secondary circuits with Biomass
@andycoo that flooring sounds ideal. Extra volume is ...
By Sune , 3 days ago
-
If you are thinking of heating on the immersion conside...
By JamesPa , 4 days ago
-
RE: Surface mount or bury primaries for heat pump installation?
@tomasmcguinness, I think your best bet would be using ...
By Aventus Eco , 5 days ago
-
RE: Solar Power Output – Let’s Compare Generation Figures
@toodles all depends on asking the right questions! And...
By Tim441 , 5 days ago