Forums

Forums
Renewable Heating
Air Source Heat Pum...
Mitsubishi Ecodan A...
 
Notifications
Clear all

Mitsubishi Ecodan ASHP general set-up and efficiency

 
Page 7 / 10
Air Source Heat Pumps (ASHPs)
Last Post by ngillam 7 months ago
120 Posts
7 Users
3 Reactions
10.2 K Views
RSS
 ngillam
(@ngillam)
Estimable Member Member
Joined: 1 year ago
Posts: 60
Topic starter 28/11/2024 9:02 am  

@gary So following your instructions I'll have 99 seconds to run through and pair (if required)?  I was hoping I could remove faceplate and switch to correct rooms if they were paired incorrectly.  Hopefully all will become clear over the weekend, I don't remember my actuators moving freely, lets see.

Cheers,

Neil.


   
ReplyQuote
 Gary
(@gary)
Prominent Member Member
Joined: 3 years ago
Posts: 350
28/11/2024 9:12 am  

@ngillam yes but only need to do one at a time unless you live in a mansion with different wings 90 seconds is a long time


   
ReplyQuote
 ngillam
(@ngillam)
Estimable Member Member
Joined: 1 year ago
Posts: 60
Topic starter 28/11/2024 11:49 am  

@gary The heating bill often looks like we live in a mansion with multiple wings.......but that's just because it gets to warm.  Next time you're in North Oxfordshire let me know....owe you multiple pints.

Neil.


   
ReplyQuote
 ngillam
(@ngillam)
Estimable Member Member
Joined: 1 year ago
Posts: 60
Topic starter 05/12/2024 3:56 pm  

Thanks to @gary my heatmisers and UFH manifolds are paired and talking to each other, although the far bedroom seems to have switch off on manifold every now and then despite heatmiser demanding heat?!

This is the latest set of numbers for the last week/24hrs.

p2
p1
p3

 Any thoughts or observations?

Thanks,

Neil.


   
ReplyQuote
 Gary
(@gary)
Prominent Member Member
Joined: 3 years ago
Posts: 350
05/12/2024 4:06 pm  

@ngillam If the far bedroom is turning on for 12 mins then off for 48mins then the wiring centre isn't getting a signal this is a fail safe that allows the circuit to operate whilst it has no connection to the thermostat.

In the melcloud app below the internal temperature section there is hourly temps and you can look at what is going on every hour for the previous 24 hours it will show you what your heat pump is doing hour by hour its useful to see how often it cycling on and off.

Below the estimated energy use plot there are bar charts for estimated consumed and delivered energy dividing delivered by consumed will give the efficiency or COP, mine when its cold like yesterday is about 3

Does your system have glycol in it, if so you can turn off the freeze stat function that operates the pumps when the HP is off, this is for 100% water systems to prevent them freezing

 

This post was modified 8 months ago 2 times by Gary

   
ReplyQuote
 ngillam
(@ngillam)
Estimable Member Member
Joined: 1 year ago
Posts: 60
Topic starter 05/12/2024 4:37 pm  

@gary Hi, Unsure what else I can do about signal to far bedroom, aerials are in but assume the timber heavy nature of the structure might hinder it?

Cycling doesn't look too bad over the last number of hours

My cop based on 12.5 consumed and 60 delivered for yesterday is 4.8

Glycol.....not sure, surely there must be a label/tag somewhere to indicate?

 

The house is still a bit too warm for us, but the flow temp is about 28, I fear cycling if I go any lower, can I adjust flow rates to somehow cool the rooms?

Thanks,

Neil.


   
ReplyQuote



 Gary
(@gary)
Prominent Member Member
Joined: 3 years ago
Posts: 350
05/12/2024 6:46 pm  

All you can really do is try lower flow rate as long as it’s only cycling once an hour that’s ok.

Only other way to reduce cycling is to ensure the max water volume is available that means removing all the actuators so all areas are heated then you may be able to run the flow temp lower

For the bathroom that’s losing connection I would remove the actuator so it’s always open then as long as one of the circuits on that manifold calls for heat then heat will always flow to the bedroom


   
ReplyQuote
 ngillam
(@ngillam)
Estimable Member Member
Joined: 1 year ago
Posts: 60
Topic starter 05/12/2024 6:56 pm  

@gary how would I remove actuators?


   
ReplyQuote
 Gary
(@gary)
Prominent Member Member
Joined: 3 years ago
Posts: 350
05/12/2024 7:01 pm  

@ngillam do they not unscrew mine do they are only hand tight but yours maybe different.

This post was modified 8 months ago by Gary

   
ReplyQuote
 ngillam
(@ngillam)
Estimable Member Member
Joined: 1 year ago
Posts: 60
Topic starter 05/12/2024 7:07 pm  

@gary so it's just a case of opening them all up? Unscrewed to the max? Never really tackled these before.....


   
ReplyQuote
 Gary
(@gary)
Prominent Member Member
Joined: 3 years ago
Posts: 350
05/12/2024 7:48 pm  

@ngillam unscrew them and take them off they hold the circuit closed when they are off the circuit is open


   
ReplyQuote
 ngillam
(@ngillam)
Estimable Member Member
Joined: 1 year ago
Posts: 60
Topic starter 05/12/2024 7:57 pm  

@gary ok, if ok with you, will take a photo and post before removing just to be on the safe side..... it'll be tomorrow though 👍


   
ReplyQuote



Page 7 / 10
Forum Jump:
  Previous Topic
Next Topic  



Share:

Join Us!

Podcast Picks

Latest Posts

Members Online

 No online members at the moment

Click to access the login or register cheese
x Powerful Protection for WordPress, from Shield Security
This Site Is Protected By
ShieldPRO →