Recent Posts

| Forums | Topics

Page 25 / 71 Prev Next

Posts with their shortened content
	RE: Midea ASHP – how to set weather compensation By cathodeRay, 1 week ago Forum Air Source Heat Pumps (ASHPs)
	I was just about to do that, and here it is. The CAP columns are the outputs at various OAT and leaving water temps (LWT , flow) in watts. As you may have picked up elsewhere, Midea units suffer from ...
	RE: Midea ASHP – how to set weather compensation By pash44pump, 1 week ago Forum Air Source Heat Pumps (ASHPs)
	This now in answer to my request to provide input assumptions for the heat loss calculations "In the scope document that Sandra shared with you, the details you are looking for can be found on pages 1...
	RE: A Customer's Lessons Learnt from a Heat Pump Installation in a Large House By JamesPa, 1 week ago Forum Air Source Heat Pumps (ASHPs)
	@drei I will say again that Im sorry to heat about your woes. Despite the fact that my heat pump install has been a sparkling success, Im angry too, albeit for a slightly different reason. I think...
	RE: Seeking Help for In-Principle Quote to fix a botched heat pump installation by Heat Geek Installer By GrahamF, 1 week ago Forum Air Source Heat Pumps (ASHPs)
	@drei I was very sorry to read this heartbreaking story. It is bad enough to feel you have been ripped off, but being cold at home with your family must make it doubly bad. On top of that, you seem ...
	RE: Midea ASHP – how to set weather compensation By pash44pump, 1 week ago Forum Air Source Heat Pumps (ASHPs)
	@jamespa how do you get from usage of 30MWh to loss between 10 and 15?
	RE: Midea ASHP – how to set weather compensation By JamesPa, 1 week ago Forum Air Source Heat Pumps (ASHPs)
	OK that's great. 3000l = 30MWh. This corresponds, almost certainly, to a loss between 10kW and 15kW. I would probably ask the installer to produce the fabric parameters fed into the program. You ca...
	RE: Midea ASHP – how to set weather compensation By cathodeRay, 1 week ago Forum Air Source Heat Pumps (ASHPs)
	You have in a way touched on the essential difference between WC and room stat based control: the former is continuously variable between X and Y (the limits of the curve), while the latter is on/off....
	RE: Midea ASHP – how to set weather compensation By pash44pump, 1 week ago Forum Air Source Heat Pumps (ASHPs)
	@jamespa Ok I have now found all my old oil orders and over a 7 year period, the average amount ordered was 2900 litres. The installer assumed an average of 3000 litres in the scope document. The hous...
	RE: Midea ASHP – how to set weather compensation By JamesPa, 1 week ago Forum Air Source Heat Pumps (ASHPs)
	@pash44pump Ok that's a bit concerning. Is the difference down to the fact the as built spec for the building departs from the design spec? If so it's possible that the ufh is not adequate (althoug...
	RE: Midea ASHP – how to set weather compensation By pash44pump, 1 week ago Forum Air Source Heat Pumps (ASHPs)
	So now I have completed my heat loss calculations and I get a total property heat loss of 12502 against the installer's calculations of 8610. I have used 2006 building regs for all ACH numbers (0.7).
	RE: Midea ASHP – how to set weather compensation By Tasos, 1 week ago Forum Air Source Heat Pumps (ASHPs)
	(a) The thermostat will work only if you exceed the desired temperature (in case WC does not work properly), to save you money. (b) if you want independent control in each room, you have to install th...
	RE: Midea ASHP – how to set weather compensation By Tasos, 1 week ago Forum Air Source Heat Pumps (ASHPs)
	WC is more stable because it modulates the inverter and thermostat based control has, currently, on-off behavior. It is not the information that is wrong, it is the way it is used. This is my point: t...